NETC02-CC Frequently Asked Questions
We extracted questions about NETC02-CC from the FAQ content on our website and summarized them based on each individual scene.
Wide-ranging support is available, including consideration, start-up, and in-operation troubleshooting. (No. of FAQs is the serial number for the entire FAQ content.)
Wide-ranging support is available, including consideration, start-up, and in-operation troubleshooting. (No. of FAQs is the serial number for the entire FAQ content.)
-
Consideration of Introduction
-
Establishing Connection and Communication
-
How to Use and Apply
-
Troubleshooting
Consideration of Introduction
Confirming Product Specifications
Establishing Connection and Communication
About Connections
- Q441: How do I connect the NETC02-CC and a driver?
- Q442: Can I use a commercially available LAN cable to connect the NETC02-CC to a driver?
- Q449: When I use NETC02-CC, do I have to set the driver address number from 0?
- Q540: I want to connect three drivers to the NETC02-CC. Can the driver be set to address number 0, 1, and 3, while address number 2 is left empty?
About Setting of Parameters and Switches
- Q446: I want to connect 4 drivers to the NETC02-CC. The host is a CC-Link master manufactured by Mitsubishi Electric Corporation. If the first address of the remote I/O of address number 0 is set to X1000 and Y1000, what will the first address of address number 1~3 be?
- Q450: What is the "remote register arrangement setting" in the operation mode setting switch of NETC02-CC?
- Q445: The extended cyclic setting of NETC02-CC includes 2x, 4x, or 8x selections - what is the difference?
- Q468: NETC02-CC has 2 types of command execution methods: command selection method and command fixation method. Please explain how to switch them. Do the switching settings or parameters need to be changed?
How to Use and Apply
Variation in Command Methods and Reading/Writing of Data
- Q461: NETC02-CC has 2 methods for writing data: the Command Selection Method and Command Fixation Method. How should I use them?
- Q470: I use a NETC02-CC. How can I write data using the command selection method?
- Q470: I use a NETC02-CC. How can I monitor the feedback position using the command selection method?
- Q462: Using the NETC02-CC, how can I rewrite multiple sets of data simultaneously using the command selection method?
- Q470: I use a NETC02-CC. How can I write data using the command fixation method?
- Q463: Although I am using the NETC02-CC with the command fixation method, I want to monitor the alarm code and feedback speed. Can the contents of the register arrangement of the command fixation method be changed?
Using Operation Commands and Functions
- Q464: I am using the NETC02-CC and AZ Series. Is there a way to run the motor immediately after setting the position data without inputting an operation signal?
- Q453: I have mixed drivers from multiple series connected to the NETC02-CC. Can the alarms of all connected axes be cleared simultaneously?
- Q456: I want to use the NETC02-CC and AZ Series to perform "positioning operation" and "continuous operation." What should I do after setting the data?
- Q465. I use NETC02-CC. There are only 3 data selection signals for remote I/O: M0, M1, and M2, and only operation data No. 0~7 are selectable. How can I select No. 8 or beyond?
About Communication Time Lag and Timing
Troubleshooting
Troubleshooting List
- Q454: The C-DAT LED on the NETC02-CC is lit up in red. What are the possible causes?
- Q459: I am using the NETC02-CC with the command selection method, but changes to the operation data and parameters are not reflected. What are the possible causes?
- Q458: I am using the NETC02-CC with the command fixation method, but the position data setting is not reflected. What are the possible causes?
- Q470: I use a NETC02-CC. If the power is turned off and on again after setting operation data or parameters using the command selection method, the data that should have been set will be lost. How do I save data and parameters?
- Q457: I have 4 drivers connected to a NETC02-CC and am using a 16-word arrangement with Command Fixation Method. The position data settings could be configured for address number 0 and 1, but not address number 2 and 3. What are the possible causes?
- Q451: I have 4 drivers connected to a NETC02-CC. There is no problem with address number 0, but address number 1~3 cannot be controlled by remote I/O nor set for operation data. What are the possible causes?